
If you’ve read a few of my reviews, you know they all start the same way: a list of features with the brand, the material, the length, the girth, the lubricant to use and the price. I do it because the product page is often the only information you have before buying, and learning to read it saves a lot of money and disappointment. Here’s how I read the numbers and words manufacturers give us, and which ones I take with a grain of salt.
Decibels
What the number means
Decibels measure loudness on a logarithmic scale, which means the numbers don’t add up the way you’d expect. An increase of 10 dB sounds roughly twice as loud to our ears, so a toy rated at 50 dB is a lot noisier than one rated at 40 dB, even though the numbers look close. For reference, a quiet room sits around 30 to 40 dB and a normal conversation around 60 dB.
Why the claims rarely match reality
There’s no standard way of measuring a sex toy’s noise. Brands rarely tell you how far from the toy the microphone was, which setting was used, or whether the toy was held in the air or resting on something. A vibrator measured on its lowest setting from a metre away will look whisper quiet on paper and sound very different on its highest setting on your nightstand. I treat a decibel rating as a rough comparison between toys from the same brand, at best.
Pitch matters as much as volume
Two toys with the same rating can be very different to live with. A high-pitched buzz carries through doors and walls much more than a low rumble. Hard surfaces amplify the sound, while blankets and bodies muffle it. And in cheaper toys, a loose part that rattles can add more noise than the motor itself. When noise matters to you, look for reviews that describe the sound, not only the number.
Power
RPM and amplitude
When a brand lists power, it usually gives you rpm, the speed at which the motor spins. That tells you about the frequency of the vibrations, but not about their amplitude, meaning how far the motor actually moves. Amplitude is what makes vibrations feel deep and strong. As a general rule, “rumbly” toys have a lower frequency with more amplitude, and “buzzy” toys have a high frequency with little movement. Brands almost never list amplitude, so this is where the words people use in reviews matter more than the numbers. My Doxy Die Cast, for example, is rated at 3,000 to 9,000 rpm, and what I noticed in use is that its lower settings feel rumblier than the higher ones.
Speeds and patterns
“Ten functions” often means three steady speeds plus seven patterns. If you don’t care about patterns, count the steady speeds and look at how low the lowest one goes. Also check how the speeds are controlled: buttons that step through set levels are predictable, while a continuous spectrum can make it hard to land on the speed you want. That was one of my small annoyances with the Doxy.
Batteries and run time
A bigger battery capacity, listed in mAh, doesn’t automatically mean a longer run time, since it depends on how hungry the motor is. Run times are usually measured on the lowest setting, so expect less at full power. Look at the charging time and the charging method too: USB, magnetic or a proprietary cable you’ll need to keep track of. Toys that run on AAA batteries are cheaper upfront but cost more over time, and mains-powered toys never run out but keep you near an outlet. I compare those two worlds in Wand Vibrators Compared: Corded vs Rechargeable.
Waterproof ratings
The most reliable information here is an IP rating. IPX7 means the toy can be fully submerged, typically up to one metre for thirty minutes. IPX4 only protects against splashes, so you can wash the toy carefully but shouldn’t drop it in the bath. Words like “water resistant” or “splash proof” without a rating should be read as “don’t submerge it”. Even on a waterproof toy, check that the charging port is sealed and dry before plugging it in.
Sizes
Total length includes the handle or base, which you can’t insert, so always look for the insertable length. For width, brands use either the diameter or the circumference, and they’re not the same thing: the circumference is roughly the diameter multiplied by 3.14. That’s why I list both in my reviews. The easiest way to know if a toy will suit you is to measure one you already own and love with a soft measuring tape or a piece of string, then compare.
Materials: words to trust and words to question
Words I trust: 100% silicone (platinum-cure is even better), borosilicate glass, ABS plastic, stainless steel with its grade stated, stone, and sealed wood. These are non-porous and can be cleaned properly.
Words I question: “silicone blend”, “sil-a-gel”, TPE, TPR, jelly, PVC, “real feel” or “cyberskin”. These are porous or unclear. Be careful as well with “phthalate-free”, which is not a material, and with “body-safe” or “hypoallergenic” when no material is named at all.
Firmness descriptions deserve a grain of salt too. When I reviewed the Tantus Echo Super Soft, “Super Soft” turned out to be closer to medium, softer than the brand’s regular silicone but nothing like a soft indie dildo. Compare within the same brand when you can.
Lube compatibility
The lubricant line in a spec list follows from the material. Silicone toys should be used with water-based lube, since silicone lube can damage some silicone over time. Glass, steel and hard plastic work with anything. If you really want to use silicone lube with a silicone toy, test it first on a small spot, like the base, and leave it there for a while before deciding.
Specs are a starting point
A spec sheet tells you what a toy is made of and roughly what it does, but it can’t tell you how it will feel to you. Read the numbers first to rule things out, then read reviews from people whose tastes you know. And if you’re shopping with a tight budget, my guide to body-safe toys under $50 will help you spot the materials worth paying for.
